[ 0.000000] Using PowerMac machine description [ 0.000000] Total memory = 1280MB; using 4096kB for hash table (at cfc00000) [ 0.000000] Linux version 2.6.31-rc5 (dummy@alice) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #8 Sat Aug 8 20:18:30 PDT 2009 [ 0.000000] Found UniNorth memory controller & host bridge @ 0xf8000000 revision: 0xd2 [ 0.000000] Mapped at 0xff7c0000 [ 0.000000] Found a Intrepid mac-io controller, rev: 0, mapped at 0xff740000 [ 0.000000] Processor NAP mode on idle enabled. [ 0.000000] PowerMac motherboard: PowerBook G4 12" [ 0.000000] via-pmu: Server Mode is disabled [ 0.000000] PMU driver v2 initialized for Core99, firmware: 0c [ 0.000000] console [udbg0] enabled [ 0.000000] Found UniNorth PCI host bridge at 0x00000000f0000000. Firmware bus number: 0->0 [ 0.000000] PCI host bridge /pci@f0000000 ranges: [ 0.000000] MEM 0x00000000f1000000..0x00000000f1ffffff -> 0x00000000f1000000 [ 0.000000] IO 0x00000000f0000000..0x00000000f07fffff -> 0x0000000000000000 [ 0.000000] MEM 0x0000000090000000..0x00000000afffffff -> 0x0000000090000000 [ 0.000000] Found UniNorth PCI host bridge at 0x00000000f2000000. Firmware bus number: 0->0 [ 0.000000] PCI host bridge /pci@f2000000 (primary) ranges: [ 0.000000] MEM 0x00000000f3000000..0x00000000f3ffffff -> 0x00000000f3000000 [ 0.000000] IO 0x00000000f2000000..0x00000000f27fffff -> 0x0000000000000000 [ 0.000000] MEM 0x0000000080000000..0x000000008fffffff -> 0x0000000080000000 [ 0.000000] Found UniNorth PCI host bridge at 0x00000000f4000000. Firmware bus number: 0->0 [ 0.000000] PCI host bridge /pci@f4000000 ranges: [ 0.000000] MEM 0x00000000f5000000..0x00000000f5ffffff -> 0x00000000f5000000 [ 0.000000] IO 0x00000000f4000000..0x00000000f47fffff -> 0x0000000000000000 [ 0.000000] nvram: Checking bank 0... [ 0.000000] nvram: gen0=791, gen1=790 [ 0.000000] nvram: Active bank is: 0 [ 0.000000] nvram: OF partition at 0x410 [ 0.000000] nvram: XP partition at 0x1020 [ 0.000000] nvram: NR partition at 0x1120 [ 0.000000] Top of RAM: 0x50000000, Total RAM: 0x50000000 [ 0.000000] Memory hole size: 0MB [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000000 -> 0x00030000 [ 0.000000] Normal 0x00030000 -> 0x00030000 [ 0.000000] HighMem 0x00030000 -> 0x00050000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00050000 [ 0.000000] On node 0 totalpages: 327680 [ 0.000000] free_area_init_node: node 0, pgdat c03d89c8, node_mem_map c0c2a000 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 195072 pages, LIFO batch:31 [ 0.000000] HighMem zone: 1024 pages used for memmap [ 0.000000] HighMem zone: 130048 pages, LIFO batch:31 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 325120 [ 0.000000] Kernel command line: root=/dev/hda6 ro [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] High memory: 524288k [ 0.000000] Memory: 1289860k/1310720k available (3808k kernel code, 19732k reserved, 136k data, 222k bss, 160k init) [ 0.000000] Kernel virtual memory layout: [ 0.000000] * 0xfffef000..0xfffff000 : fixmap [ 0.000000] * 0xff800000..0xffc00000 : highmem PTEs [ 0.000000] * 0xfde72000..0xff800000 : early ioremap [ 0.000000] * 0xf1000000..0xfde72000 : vmalloc & ioremap [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:512 [ 0.000000] mpic: Setting up MPIC " MPIC 1 " version 1.2 at 80040000, max 4 CPUs [ 0.000000] mpic: ISU size: 64, shift: 6, mask: 3f [ 0.000000] mpic: Initializing for 64 sources [ 0.000000] GMT Delta read from XPRAM: 0 minutes, DST: off [ 0.000000] time_init: decrementer frequency = 18.432000 MHz [ 0.000000] time_init: processor frequency = 1499.999994 MHz [ 0.000000] clocksource: timebase mult[d9038e4] shift[22] registered [ 0.000000] clockevent: decrementer mult[4b7f5a5] shift[32] cpu[0] [ 0.000335] Console: colour dummy device 80x25 [ 0.000559] console handover: boot [udbg0] -> real [tty0] [ 0.000839] Mount-cache hash table entries: 512 [ 0.001242] device-tree: Duplicate name in /cpus/PowerPC,G4@0, renamed to "l2-cache#1" [ 0.004911] NET: Registered protocol family 16 [ 0.006044] irq: irq 42 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 42 [ 0.006081] KeyWest i2c @0xf8001003 irq 42 /uni-n@f8000000/i2c@f8001000 [ 0.006098] channel 1 bus /uni-n@f8000000/i2c@f8001000/i2c-bus@1 [ 0.006137] irq: irq 26 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 26 [ 0.006156] KeyWest i2c @0x80018000 irq 26 /pci@f2000000/mac-io@17/i2c@18000 [ 0.006171] channel 0 bus /pci@f2000000/mac-io@17/i2c@18000/i2c-bus@0 [ 0.006196] PMU i2c /pci@f2000000/mac-io@17/via-pmu@16000/pmu-i2c [ 0.006215] channel 1 bus [ 0.006223] channel 2 bus [ 0.006305] irq: irq 25 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 25 [ 0.006335] irq: irq 47 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 47 [ 0.006546] PCI: Probing PCI hardware [ 0.006765] pci 0000:00:10.0: reg 10 32bit mmio: [0x91000000-0x91ffffff] [ 0.006776] pci 0000:00:10.0: reg 14 32bit mmio: [0xa0000000-0xa7ffffff] [ 0.006798] pci 0000:00:10.0: reg 30 32bit mmio: [0x90000000-0x9001ffff] [ 0.006876] irq: irq 48 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 48 [ 0.007256] pci 0001:10:12.0: reg 10 32bit mmio: [0x80084000-0x80085fff] [ 0.007300] pci 0001:10:12.0: supports D1 D2 [ 0.007306] pci 0001:10:12.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.007323] pci 0001:10:12.0: PME# disabled [ 0.007360] pci 0001:10:17.0: reg 10 32bit mmio: [0x80000000-0x8007ffff] [ 0.007414] pci 0001:10:18.0: reg 10 32bit mmio: [0x000000-0x000fff] [ 0.007472] pci 0001:10:19.0: reg 10 32bit mmio: [0x000000-0x000fff] [ 0.007534] pci 0001:10:1a.0: reg 10 32bit mmio: [0x80083000-0x80083fff] [ 0.007599] pci 0001:10:1b.0: reg 10 32bit mmio: [0x80082000-0x80082fff] [ 0.007643] pci 0001:10:1b.0: supports D1 D2 [ 0.007648] pci 0001:10:1b.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.007663] pci 0001:10:1b.0: PME# disabled [ 0.007705] pci 0001:10:1b.1: reg 10 32bit mmio: [0x80081000-0x80081fff] [ 0.007748] pci 0001:10:1b.1: supports D1 D2 [ 0.007754] pci 0001:10:1b.1: PME# supported from D0 D1 D2 D3hot D3cold [ 0.007769] pci 0001:10:1b.1: PME# disabled [ 0.007811] pci 0001:10:1b.2: reg 10 32bit mmio: [0x80080000-0x800800ff] [ 0.007854] pci 0001:10:1b.2: supports D1 D2 [ 0.007860] pci 0001:10:1b.2: PME# supported from D0 D1 D2 D3hot D3cold [ 0.007874] pci 0001:10:1b.2: PME# disabled [ 0.007934] irq: irq 52 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 52 [ 0.007969] irq: irq 27 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 27 [ 0.008000] irq: irq 28 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 28 [ 0.008030] irq: irq 29 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 29 [ 0.008057] irq: irq 63 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 63 [ 0.009156] pci 0002:20:0d.0: reg 10 32bit mmio: [0xf5004000-0xf5007fff] [ 0.009210] pci 0002:20:0e.0: reg 10 32bit mmio: [0xf5000000-0xf5000fff] [ 0.009246] pci 0002:20:0e.0: supports D1 D2 [ 0.009252] pci 0002:20:0e.0: PME# supported from D0 D1 D2 D3hot [ 0.009267] pci 0002:20:0e.0: PME# disabled [ 0.009296] pci 0002:20:0f.0: reg 10 32bit mmio: [0xf5200000-0xf53fffff] [ 0.009320] pci 0002:20:0f.0: reg 30 32bit mmio: [0xf5100000-0xf51fffff] [ 0.009383] irq: irq 39 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 39 [ 0.009410] irq: irq 40 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 40 [ 0.009439] irq: irq 41 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 41 [ 0.009953] pci_bus 0000:00: resource 0 io: [0x802000-0x1001fff] [ 0.009961] pci_bus 0000:00: resource 1 mem: [0xf1000000-0xf1ffffff] [ 0.009969] pci_bus 0000:00: resource 2 mem: [0x90000000-0xafffffff] [ 0.009976] pci_bus 0001:10: resource 0 io: [0x00-0x7fffff] [ 0.009982] pci_bus 0001:10: resource 1 mem: [0xf3000000-0xf3ffffff] [ 0.009990] pci_bus 0001:10: resource 2 mem: [0x80000000-0x8fffffff] [ 0.009997] pci_bus 0002:20: resource 0 io: [0xff7fe000-0xffffdfff] [ 0.010004] pci_bus 0002:20: resource 1 mem: [0xf5000000-0xf5ffffff] [ 0.013104] bio: create slab at 0 [ 0.013699] usbcore: registered new interface driver usbfs [ 0.013786] usbcore: registered new interface driver hub [ 0.013904] usbcore: registered new device driver usb [ 0.015188] NET: Registered protocol family 2 [ 0.015260] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.015682] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.016365] Switched to high resolution mode on CPU 0 [ 0.017829] TCP bind hash table entries: 65536 (order: 6, 262144 bytes) [ 0.018402] TCP: Hash tables configured (established 131072 bind 65536) [ 0.018425] TCP reno registered [ 0.018588] NET: Registered protocol family 1 [ 0.018898] setup_kcore: restrict size=3fffffff [ 0.019117] Registering PowerMac CPU frequency driver [ 0.019140] Low: 749 Mhz, High: 1499 Mhz, Boot: 749 Mhz [ 0.019859] highmem bounce pool size: 64 pages [ 0.027705] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled [ 0.028573] msgmni has been set to 1497 [ 0.028784] io scheduler noop registered [ 0.028801] io scheduler anticipatory registered [ 0.028815] io scheduler deadline registered (default) [ 0.028859] io scheduler cfq registered [ 0.029587] nvidiafb: Device ID: 10de0329 [ 0.044341] nvidiafb: CRTC0 analog not found [ 0.060337] nvidiafb: CRTC1 analog not found [ 0.160148] i2c-adapter i2c-0: unable to read EDID block. [ 0.312143] i2c-adapter i2c-0: unable to read EDID block. [ 0.464142] i2c-adapter i2c-0: unable to read EDID block. [ 0.516361] nvidiafb: Found OF EDID for head 1 [ 0.516370] nvidiafb: EDID found from BUS1 [ 0.616144] i2c-adapter i2c-1: unable to read EDID block. [ 0.768143] i2c-adapter i2c-1: unable to read EDID block. [ 0.920142] i2c-adapter i2c-1: unable to read EDID block. [ 0.972358] nvidiafb: CRTC 1 is currently programmed for DFP [ 0.972375] nvidiafb: Using DFP on CRTC 1 [ 0.972390] nvidiafb: Panel size is 1024 x 768 [ 0.972405] nvidiafb: Panel is TMDS [ 0.974331] nvidia: Backlight initialized (nvidiabl0) [ 0.974871] nvidiafb: Flat panel dithering enabled [ 0.977365] Console: switching to colour frame buffer device 128x48 [ 0.979960] nvidiafb: PCI nVidia NV32 framebuffer (64MB @ 0xA0000000) [ 0.986061] Generic RTC Driver v1.07 [ 0.986211] Generic non-volatile memory driver v1.1 [ 0.986399] MacIO PCI driver attached to Intrepid chipset [ 0.987045] irq: irq 32 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 32 [ 0.987532] irq: irq 24 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 24 [ 0.987551] irq: irq 12 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 16 [ 0.987681] irq: irq 22 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 22 [ 0.987700] irq: irq 5 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 17 [ 0.987718] irq: irq 6 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 18 [ 0.987881] irq: irq 23 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 23 [ 0.987900] irq: irq 7 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 19 [ 0.987918] irq: irq 8 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 20 [ 0.988707] Uniform Multi-Platform E-IDE driver [ 0.988815] adb: starting probe task... [ 0.990116] ide-pmac 0002:20:0d.0: enabling device (0000 -> 0002) [ 1.014745] adb devices: [2]: 2 c4 [7]: 7 1f [ 1.020232] ADB keyboard at 2, handler 1 [ 1.020282] Detected ADB keyboard, type ISO, swapping keys. [ 1.020539] input: ADB keyboard as /devices/virtual/input/input0 [ 1.020741] input: ADB Powerbook buttons as /devices/virtual/input/input1 [ 1.020796] adb: finished probe task... [ 2.008343] ide-pmac: Found Apple UniNorth ATA-6 controller (PCI), bus ID 3, irq 39 [ 2.008424] Probing IDE interface ide0... [ 2.296527] hda: Hitachi HTS541060G9AT00, ATA DISK drive [ 2.968448] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4 [ 2.968696] hda: UDMA/100 mode selected [ 2.968987] ide0 at 0xf102a000-0xf102a070,0xf102a160 on irq 39 [ 3.988342] ide-pmac: Found Apple KeyLargo ATA-3 controller (macio), bus ID 0, irq 24 [ 3.989611] Probing IDE interface ide1... [ 4.388530] hdc: MATSHITACD-RW CW-8123, ATAPI CD/DVD-ROM drive [ 4.724462] hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4 [ 4.724631] hdc: MWDMA2 mode selected [ 4.726078] ide1 at 0xf1024000-0xf1024070,0xf1024160 on irq 24 [ 4.727489] ide-gd driver 1.18 [ 4.728749] hda: max request size: 512KiB [ 4.752634] hda: 117210240 sectors (60011 MB) w/7539KiB Cache, CHS=16383/255/63 [ 4.754272] hda: cache flushes supported [ 4.755619] hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7 [ 4.770597] sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com) [ 4.836690] PHY ID: 4061e4, addr: 0 [ 4.837481] eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:14:51:02:05:86 [ 4.838799] eth0: Found BCM5221 PHY [ 4.840272] usbcore: registered new interface driver libusual [ 4.841720] mice: PS/2 mouse device common for all mice [ 4.843394] TCP cubic registered [ 4.845473] NET: Registered protocol family 10 [ 4.847057] lo: Disabled Privacy Extensions [ 4.848577] IPv6 over IPv4 tunneling driver [ 4.850207] sit0: Disabled Privacy Extensions [ 4.851618] NET: Registered protocol family 17 [ 4.853289] registered taskstats version 1 [ 4.855066] input: PMU as /devices/virtual/input/input2 [ 4.856656] Registered led device: pmu-front-led [ 4.895157] kjournald starting. Commit interval 5 seconds [ 4.896581] EXT3-fs: mounted filesystem with writeback data mode. [ 4.897991] VFS: Mounted root (ext3 filesystem) readonly on device 3:6. [ 4.899434] Freeing unused kernel memory: 160k init [ 6.641373] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 6.642953] Apple USB OHCI 0001:10:18.0 disabled by firmware [ 6.644648] Apple USB OHCI 0001:10:19.0 disabled by firmware [ 6.646123] ohci_hcd 0001:10:1a.0: enabling device (0000 -> 0002) [ 6.647556] ohci_hcd 0001:10:1a.0: OHCI Host Controller [ 6.648984] ohci_hcd 0001:10:1a.0: new USB bus registered, assigned bus number 1 [ 6.650443] ohci_hcd 0001:10:1a.0: irq 29, io mem 0x80083000 [ 6.675907] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.677421] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after [ 6.730289] usb usb1: configuration #1 chosen from 1 choice [ 6.731851] hub 1-0:1.0: USB hub found [ 6.733299] hub 1-0:1.0: 2 ports detected [ 6.734851] ehci_hcd 0001:10:1b.2: enabling device (0004 -> 0006) [ 6.736265] ehci_hcd 0001:10:1b.2: EHCI Host Controller [ 6.737643] ehci_hcd 0001:10:1b.2: new USB bus registered, assigned bus number 2 [ 6.739064] ehci_hcd 0001:10:1b.2: Enabling legacy PCI PM [ 6.764442] ehci_hcd 0001:10:1b.2: irq 63, io mem 0x80080000 [ 6.776474] ehci_hcd 0001:10:1b.2: USB 2.0 started, EHCI 1.00 [ 6.778147] usb usb2: configuration #1 chosen from 1 choice [ 6.779559] hub 2-0:1.0: USB hub found [ 6.781141] hub 2-0:1.0: 5 ports detected [ 6.888380] ide-cd driver 5.00 [ 6.904719] ohci_hcd 0001:10:1b.0: enabling device (0000 -> 0002) [ 6.906165] ohci_hcd 0001:10:1b.0: OHCI Host Controller [ 6.907482] ohci_hcd 0001:10:1b.0: new USB bus registered, assigned bus number 3 [ 6.908846] ohci_hcd 0001:10:1b.0: irq 63, io mem 0x80082000 [ 6.916284] PowerMac i2c bus pmu 2 registered [ 6.917698] PowerMac i2c bus pmu 1 registered [ 6.919022] PowerMac i2c bus mac-io 0 registered [ 6.920348] PowerMac i2c bus uni-n 1 registered [ 6.952561] ide-cd: hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache [ 6.954021] Uniform CD-ROM driver Revision: 3.20 [ 6.986265] usb usb3: configuration #1 chosen from 1 choice [ 6.987717] hub 3-0:1.0: USB hub found [ 6.989076] hub 3-0:1.0: 3 ports detected [ 6.990517] ohci_hcd 0001:10:1b.1: enabling device (0000 -> 0002) [ 6.991869] ohci_hcd 0001:10:1b.1: OHCI Host Controller [ 6.993201] ohci_hcd 0001:10:1b.1: new USB bus registered, assigned bus number 4 [ 6.994548] ohci_hcd 0001:10:1b.1: irq 63, io mem 0x80081000 [ 7.060413] usb 1-1: new full speed USB device using ohci_hcd and address 2 [ 7.137200] usb usb4: configuration #1 chosen from 1 choice [ 7.138681] hub 4-0:1.0: USB hub found [ 7.140047] hub 4-0:1.0: 2 ports detected [ 7.236530] eth0: Link is up at 100 Mbps, full-duplex. [ 7.258777] usb 1-1: configuration #1 chosen from 1 choice [ 7.388431] usb 1-2: new full speed USB device using ohci_hcd and address 3 [ 7.554746] usb 1-2: configuration #1 chosen from 1 choice [ 7.668429] usb 2-2: new high speed USB device using ehci_hcd and address 2 [ 7.803909] usb 2-2: configuration #1 chosen from 1 choice [ 7.843950] irq: irq 57 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 57 [ 7.844000] irq: irq 58 on host /pci@f2000000/mac-io@17/interrupt-controller@40000 mapped to virtual irq 58 [ 7.850121] ams: Found I2C based motion sensor [ 7.906733] SCSI subsystem initialized [ 7.949269] Initializing USB Mass Storage driver... [ 7.953310] scsi0 : SCSI emulation for USB Mass Storage devices [ 7.958521] usbcore: registered new interface driver usb-storage [ 7.959864] USB Mass Storage support registered. [ 7.961195] usb-storage: device found at 2 [ 7.961201] usb-storage: waiting for device to settle before scanning [ 9.750027] EXT3 FS on hda6, internal journal [ 10.569805] loop: module loaded [ 10.667738] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com [ 11.268095] alg: No test for stdrng (krng) [ 12.078695] Adding 1171864k swap on /dev/mapper/cryptswap. Priority:1 extents:1 across:1171864k [ 12.514510] eth0: Link is up at 100 Mbps, full-duplex. [ 12.515926] eth0: Pause is disabled [ 12.961755] scsi 0:0:0:0: Direct-Access WDC WD10 EACS-00D6B0 01.0 PQ: 0 ANSI: 4 [ 12.966028] scsi 0:0:0:1: Direct-Access WDC WD10 EACS-00D6B0 01.0 PQ: 0 ANSI: 4 [ 12.968073] usb-storage: device scan complete [ 14.130088] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) [ 14.131948] sd 0:0:0:1: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) [ 14.133687] sd 0:0:0:0: [sda] Write Protect is off [ 14.135143] sd 0:0:0:0: [sda] Mode Sense: 11 00 00 00 [ 14.135149] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 14.136941] sd 0:0:0:1: [sdb] Write Protect is off [ 14.138399] sd 0:0:0:1: [sdb] Mode Sense: 11 00 00 00 [ 14.138425] sd 0:0:0:1: [sdb] Assuming drive cache: write through [ 14.141935] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 14.143396] sda: [ 14.143688] sd 0:0:0:1: [sdb] Assuming drive cache: write through [ 14.146611] sdb: sda1 [ 14.270965] sdb1 [ 14.307811] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 14.309380] sd 0:0:0:0: [sda] Attached SCSI disk [ 14.311183] sd 0:0:0:1: [sdb] Assuming drive cache: write through [ 14.312680] sd 0:0:0:1: [sdb] Attached SCSI disk [ 15.330309] RPC: Registered udp transport module. [ 15.331822] RPC: Registered tcp transport module. [ 15.508282] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 18.910922] svc: failed to register lockdv1 RPC service (errno 97). [ 18.914228] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory [ 18.973126] NFSD: starting 90-second grace period [ 22.892364] eth0: no IPv6 routers present [ 96.820550] EXT4-fs (dm-1): barriers enabled [ 96.840820] kjournald2 starting: pid 1840, dev dm-1:8, commit interval 5 seconds [ 96.841337] EXT4-fs (dm-1): delayed allocation enabled [ 96.841827] EXT4-fs: file extents enabled [ 96.987745] EXT4-fs: mballoc enabled [ 96.988277] EXT4-fs (dm-1): mounted filesystem with ordered data mode [ 100.868420] XFS mounting filesystem dm-2 [ 101.394504] Ending clean XFS mount for filesystem: dm-2 [ 829.683882] usb 2-1: new high speed USB device using ehci_hcd and address 3 [ 829.816880] usb 2-1: configuration #1 chosen from 1 choice [ 829.821174] scsi1 : SCSI emulation for USB Mass Storage devices [ 829.821942] usb-storage: device found at 3 [ 829.821948] usb-storage: waiting for device to settle before scanning [ 834.821588] scsi 1:0:0:0: Direct-Access SanDisk Cruzer 8.01 PQ: 0 ANSI: 0 CCS [ 834.825649] scsi 1:0:0:1: CD-ROM SanDisk Cruzer 8.01 PQ: 0 ANSI: 0 [ 834.827038] usb-storage: device scan complete [ 834.827549] sd 1:0:0:0: [sdc] 3907711 512-byte logical blocks: (2.00 GB/1.86 GiB) [ 834.829143] sd 1:0:0:0: [sdc] Write Protect is off [ 834.829638] sd 1:0:0:0: [sdc] Mode Sense: 45 00 00 08 [ 834.829644] sd 1:0:0:0: [sdc] Assuming drive cache: write through [ 834.832457] sd 1:0:0:0: [sdc] Assuming drive cache: write through [ 834.832972] sdc: [ 834.835959] sd 1:0:0:0: [sdc] Assuming drive cache: write through [ 834.836524] sd 1:0:0:0: [sdc] Attached SCSI removable disk [ 1129.210196] usb 2-1: USB disconnect, address 3 [59111.192791] EXT4-fs (dm-1): internal journal on dm-1:8 [90776.618122] adt746x: version 1 (supported) [90776.618644] adt746x: Thermostat bus: 1, address: 0x2e, limit_adjust: 0, fan_speed: -1 [90776.619135] sensor 0: HDD BOTTOMSIDE [90776.619604] sensor 1: CPU TOPSIDE [90776.620111] sensor 2: GPU ON DIE [90776.630767] adt746x: ADT7467 initializing [90776.645386] adt746x: Lowering max temperatures from 73, 80, 109 to 70, 50, 70 [90780.657037] adt746x: Putting max temperatures back from 70, 50, 70 to 73, 80, 109 [90804.693705] adt746x: version 1 (supported) [90804.694259] adt746x: Thermostat bus: 1, address: 0x2e, limit_adjust: 0, fan_speed: 255 [90804.694785] sensor 0: HDD BOTTOMSIDE [90804.695291] sensor 1: CPU TOPSIDE [90804.695811] sensor 2: GPU ON DIE [90804.709354] adt746x: ADT7467 initializing [90804.712874] adt746x: Lowering max temperatures from 73, 80, 109 to 70, 50, 70 [90824.753036] adt746x: Putting max temperatures back from 70, 50, 70 to 73, 80, 109 [91135.502016] adt746x: version 1 (supported) [91135.502587] adt746x: Thermostat bus: 1, address: 0x2e, limit_adjust: 0, fan_speed: -1 [91135.503132] sensor 0: HDD BOTTOMSIDE [91135.503662] sensor 1: CPU TOPSIDE [91135.504213] sensor 2: GPU ON DIE [91135.517917] adt746x: ADT7467 initializing [91135.521464] adt746x: Lowering max temperatures from 73, 80, 109 to 70, 50, 70 [91139.529032] adt746x: Putting max temperatures back from 70, 50, 70 to 73, 80, 109 [91147.717849] adt746x: version 1 (supported) [91147.718465] adt746x: Thermostat bus: 1, address: 0x2e, limit_adjust: 0, fan_speed: 254 [91147.719055] sensor 0: HDD BOTTOMSIDE [91147.719620] sensor 1: CPU TOPSIDE [91147.720201] sensor 2: GPU ON DIE [91147.733801] adt746x: ADT7467 initializing [91147.737392] adt746x: Lowering max temperatures from 73, 80, 109 to 70, 50, 70 [91211.865053] adt746x: Putting max temperatures back from 70, 50, 70 to 73, 80, 109 [91268.554352] adt746x: version 1 (supported) [91268.554982] adt746x: Thermostat bus: 1, address: 0x2e, limit_adjust: 0, fan_speed: 255 [91268.555577] sensor 0: HDD BOTTOMSIDE [91268.556167] sensor 1: CPU TOPSIDE [91268.556739] sensor 2: GPU ON DIE [91268.570419] adt746x: ADT7467 initializing [91268.574119] adt746x: Lowering max temperatures from 73, 80, 109 to 70, 50, 70 [91282.605032] adt746x: Putting max temperatures back from 70, 50, 70 to 73, 80, 109 [91287.897762] adt746x: version 1 (supported) [91287.898396] adt746x: Thermostat bus: 1, address: 0x2e, limit_adjust: 0, fan_speed: 240 [91287.899009] sensor 0: HDD BOTTOMSIDE [91287.899593] sensor 1: CPU TOPSIDE [91287.900191] sensor 2: GPU ON DIE [91287.913825] adt746x: ADT7467 initializing [91287.917327] adt746x: Lowering max temperatures from 73, 80, 109 to 70, 50, 70 [91295.934822] adt746x: Putting max temperatures back from 70, 50, 70 to 73, 80, 109 [91415.562322] process `sysctl' is using deprecated sysctl (syscall) net.ipv6.neigh.default.retrans_time; Use net.ipv6.neigh.default.retrans_time_ms instead.